However, in additional severe cases it will indicate you have got a failing rotor position detector, a broken motor, or broken detector or motor wires.

First Steps to require

To determine if the error code is being shown thanks to a significant wash load you must 1st try and reset the machine.

Follow these steps to finish this process:

√ Press the facility button to shut the washer off.

√ Unplug the washer from the wall or flip the circuit breaker.

√ While the facility is disengaged, press and hold the START/PAUSE button for a minimum of five seconds.

√ Flip the breaker back to the “on” position or plug the washer back to the wall.

√ Did this do the trick? If the code isn't cleared you may have to be compelled to continue troubleshooting the opposite problems.

How To Troubleshoot & Fix A barred Rotor

If the lupus code on your LG washer is in the midst of loud “clanking” noises you’ll have to be compelled to check the rotor on the unit.

Here’s however you act this:

1. 1st undo the facility wire from the wall and switch the body of water water provides off and disconnect all hoses.

2. Pull the washer way enough forward that you just will simply gain access to the rear of the machine.

3. Next, you’ll have to be compelled to take away the screws on the rear of the washer that hold the rear panel in situ.

Flex the panel enough to unleash the tabs found at the highest or bottom (location depends on your model).

4. take away the bolt that attaches the rotor to the bathtub shaft. you'll have to be compelled to hold the rotor still whereas you torsion the bolt.

5. Since there is also sharp edges concerned, it’s extremely counseled that you just wear gloves once doing this method.

6. Grasp the rotor firmly and pull it like a shot the shaft.

Once you have got the rotor off, you’ll need to envision the teeth to envision if any area unit missing or if they're stripped.

If so, you’ll merely get the new half and replace it.

How To Troubleshoot & Repair A failing Rotor Position detector

√ The rotor position detector (RPS), or hall detector, is a crucial a part of your washer’s machine-controlled system.

√ It assists the instrument panel with deciding everything is functioning usually.

√ The hall detector monitors the motor in your washer and makes certain it runs properly.

√ If this detector fails it will cause the lupus error code. Here’s a way to replace it:

1. For this fix you may disconnect all power from the machine.

2. Pull it way enough forward therefore you'll access the rear panel.

3. Next, you’ll take away the screws on the rear of the washer that hold the rear panel in situ. Pull abreast of the panel to unleash it.

4. take away the bolt that holds the rotor to the bathtub shaft.

You may have to be compelled to hold the rotor whereas you loosen the bolt.

It additionally works well to own somebody open the washer door and hold the bathtub within therefore it doesn’t move.

Again, sporting gloves could be a nice plan as you'll encounter some sharp edges.

5. Grasp the rotor and pull it off.

The rotor position detector is found at very cheap of the stator coil.

6. You’ll have to be compelled to unscrew 2|a handful|some} screws to permit you to detach two connectors.

7. once the screws area unit take awayd you’ll have to be compelled to remove all bolts holding the stator coil in situ.

Just take care to carry the stator coil as you take away the last bolt therefore it doesn’t fall off.

8. Once the stator coil is loose you’ll merely fold it down and you’ll clearly see the RPS.

9. currently take away the 2 wiring harnesses from the switches.

10. take away the RPS from the stator coil and snap the new one in situ. .

Reassemble your washer and therefore the issue ought to be gone.

If this repair didn’t fix your issue you’ll have to be compelled to check the motor and see if the detector wires area unit broken.

How To Troubleshoot & Repair broken Motor Or detector Wires

•While you have got the rear off of your LG washer and you’re gazing the RPS and rotor, it’s an excellent plan to envision for any broken wires during this space.

•The lupus code may be caused by a problem like this.

•So, before you purchase any replacement components you'll need to envision the wires.

To do therefore you would like to follow steps one through six to break up the washer.

1. Once you have got the stator coil off and you'll visibly see the wiring harnesses that connect with the motor and therefore the rotor position detector, check for wires that area unit burned or broken in a way.

You’ll see wire colours red, yellow, and blue.

2. If you discover any wires that have sustained harm it’s vital to repair them.

To do therefore you'll use heat shrink to reconnect the wires.

3. If they're too broken to carry with this repair you may have to be compelled to take away and replace the wires with new ones.

If you’ve tried all repairs we’ve steered higher than and your LG washer remains displaying the lupus error code you may quite doubtless have to be compelled to contact LG’s support center or a neighborhood appliance skilled worker.

The issues we’ve mentioned area unit the foremost common reasons the lupus error code can show, however, from time to time there is also different problems.